Skip to main content

A panel saw


I've been trying to buy a panel saw (sheet saw?) for some time, but have been told that they havn't been made for many years. I was lent one a year or two ago, and found it much better for cutting large sheets of brass than the jigsaw I had been using.

As I can't just buy one, I took an old wood saw, and ground off the cutting points. I then made up brackets to mount a fine-toothed 12 inch hacksaw blade, and drilled the saw blade to suit (A solid carbide drill goes straight through the saw steel)

It might look a bit odd - but it works. Its as easy as can be to cut a straight line right through a 4 ft by 2 ft brass sheet. I might get round to tidying the saw up - the real thing is styled like a tenon saw without the tenon. And there seems to be no need for a blade tensioner because of the way the saw works.

Comments

Dianne said…
Hey this was Brilliant Mr Normal.
My Dad was a Carpenter and could build almost anything. He allways had a shed where he would make his stuff, I'll never for get the smell of fesh ciut wood every time I would walk in there.. Watching you build your trains reminds me of my Dad . Nice memories thanks for those..
May 22, 2007 at 9:01 PM
Post a Comment

Popular posts from this blog

Coupling Rods

The spacing of the coupling rod centres is critical to the free running of the loco. I measure each side separately and comparing it with the drawing. Any inaccuracies in making up the axle-boxes or in setting the crank-pins will show up here. I started by marking out the centres and outline on the rod blank, then drilled the centres, starting with a small centre drill, then drilling out at (say) 2BA clearance at one end, and 2BA tapping at the other. The rods tapered from 3/8 to 1/4 in. - i.e a taper of 1/16 in. on each side. So I marked out the centre line on the support bar, and another, offset by 1/16 in. I drilled and tapped a fixing for one end of the bar on the centre line, and attached the rod blank. Then I lined up the other centre on the 1/16 in offset line, clamped and drilled through 2BA tapping. Now I removed the rod blank, and opened the 2BA tapping hole on the rod blank to 2BA clearance. Also I tapped 2BA threads in the support bar and bolted the two together. I clampe...
3 comments
Read more
Work has progressed - the boiler is now complete. The assembly sequence I used was as described in Alex Farmers book on boiler making - and, as it happens, his was also a GWR boiler, although bigger. As the assembly gets bigger, it always surprises me just how much heat it needs. I work outside, so can only work on wind-free ( and preferably dry) days. Also, I find it essential to use refractory bricks- without them, I'd never get up to temperature. Even so, it needed two good sized gas torches, and occasional oxy-propane, to complete the assembly. I couldn't do this alone, and gratefully thank George and Russell for their help. Where ever possible (and that's most of the time), we worked with pre-placed solder - its much easier than applying a stick, as it tends to melt - or at least sag - if you're not quick. We put rings of silver solder under the heads of all the rivet - stays in the firebox. As the solder flowed, each was grasped on the outside with pliers, rotated...
2 comments
Read more

Tender Body

The original drawings showed what I think is the Hawksworth tender - I've previously made one in 5 in gauge, and thought the Collett tender would make an interesting change. It has a couple of major challenges - the top of the sides are flared, and also the rear corners of the tand are very rounded, so a tricky compound curve is created where they meet. I took the basic dimentions from the drawings, and scaled the Collet specifics from a couple of photographs. The fact that the major lines of the tender matched up with the profile of the cab gave me some useful reference points. Then there's a raised extension which fits on top. I left a tab which I curved to match the lower part of the tender, and riveted and soldered the two together. The other tricky bit was the rivets -there are several hunders of them, and they're very prominent. My solution was to make the tender tank out of thinner brass than usual -about 22 gauge. (Another reason for this was that I had a couple ...
2 comments
Read more